1. <tbody id="cpb4d"><noscript id="cpb4d"></noscript></tbody>

      Welcome to the official website of Taizhou Jiaoxing Transmission Equipment Co., Ltd.!

      HOME  |  Online message  |  contact us


      Company news

      POSITION: HOME > NEWS > Company news

      How to Choose Reducer

      2018-12-25 11:00:17 clicks:12
      The selection of general reducer includes the steps of putting forward original conditions, selecting types and determining specifications.
      In contrast, the selection of type is relatively simple, and the key to the correct and reasonable selection of specifications of general reducer is to accurately provide the working conditions of reducer and master the design, manufacture and use characteristics of reducer. Specification selection should satisfy the conditions of strength, thermal balance and radial load bearing at the axle extension part.
      Selection of specifications according to mechanical power or torque (strength check)
      The biggest difference between the general reducer and the special reducer is that the former is suitable for all industries, but the deceleration can only be designed according to a specific working condition. Therefore, the users should consider different correction coefficients according to their respective requirements when selecting the general reducer and the special reducer. The factory should use the nameplate according to the actual motor power (not the rated power of the decelerator); the latter should use the special conditions of the users. In design, the coefficients considered are generally considered in design. The method is relatively simple as long as the power used is less than or equal to the rated power of the reducer.
      II. Calibration of Heat Balance
      The allowable heat power value of general reducer is determined by the maximum allowable equilibrium temperature of lubricating oil (generally 85 C) under specific working conditions (general ambient temperature 20 C, 100% per hour, continuous operation, power utilization rate 100%). Conditions are modified according to the corresponding coefficients (sometimes synthesized into a coefficient).
      3. Check the radial load on the extension part of the axle
      The general reducer often has to limit the maximum radial load allowed on the middle part of the extension of the input shaft and the output shaft. It should be checked. When exceeding the limit, the requirement of increasing the diameter of the shaft and the bearing should be put forward to the manufacturer.

      欧美日韩一卡2卡三卡4卡棋牌,国产亚洲一卡2卡3卡4卡,国产亚洲2018一卡2卡3卡4卡网站,成片卡1卡2卡三卡2021,欧洲色妞AV永久一区二区AV开 欧美日韩一本到卡二卡三卡免费乱码| 欧洲一卡2卡三卡4卡乱码毛1| 欧美日韩一卡2卡3卡4卡5卡在线| 欧美日韩乱码1卡2卡3卡4卡| 成片一本二卡三卡四卡无卡免费高| 欧洲一卡二卡3卡4卡网站| 精品一卡2卡三卡4卡乱码| 欧美日韩一卡2卡三卡4卡乱码视频| 成片色妞AV永久一区二区AV开| 欧洲一卡三卡四卡免费网站| 精品一卡2卡3卡4卡| 精品一卡2卡三卡4卡乱码| 国产亚洲卡一卡二卡三新区| 精品一卡2卡三卡4卡棋牌| 精品一本大道卡2卡3卡4卡| 欧洲卡一卡二卡三| 欧美日韩一卡2卡3卡4卡乱码网站导航| 精品一卡2卡3卡4卡乱码在线| 欧洲一卡二卡3卡四卡| 欧美日韩2020卡二卡三卡四乱码| 欧美日韩一卡2卡3卡4卡乱码网站导航| 成片一卡2卡3卡4卡乱码在线| 国产亚洲一区二区三区| 成片一卡2卡3卡4卡5卡视频| 欧美日韩一卡2卡三卡四卡高清| 欧洲2021卡一卡二乱码| 成片一卡2卡3卡4卡乱码网站导航| 成片中一卡2卡三卡4卡网站| 国产亚洲一卡二卡三乱码免费天美传媒在线| 欧美日韩一卡2卡三卡4卡乱码毛1| 成片一卡2卡三卡4卡乱码视频| 国产亚洲一卡2卡3卡4卡乱码在线| 欧美日韩一卡2卡3卡4卡乱码网站导航| 欧美日韩一卡二卡≡卡四卡免费视频| 欧洲卡1卡2卡三卡2021| 国产亚洲卡1卡2乱码免费| 精品2020卡二卡三卡四乱码| 成片一卡2卡三卡4卡 乱码| 国产亚洲一卡二卡≡卡四卡在线视频| 精品2018一卡2卡3卡4卡网站| 欧美日韩1卡二卡三卡4卡| 欧洲一卡2卡3卡4卡网站| 欧洲一卡三卡四区一卡三卡| 欧洲一本大道卡2卡3卡4卡| 欧美日韩一卡2卡3卡4卡国色天香| 成片不卡一卡2卡三卡4卡网站| 欧洲一卡二卡3卡4卡网站| 欧洲不卡二卡三卡四卡免费| 欧洲一卡2卡3卡4卡5卡在线| 欧洲一卡三卡四区一卡三卡| 欧洲一卡2卡三卡四卡高清| 欧美日韩2018一卡2卡3卡4卡网站| 精品一本大道卡2卡3卡4卡| 欧洲一卡二卡3卡4卡网站| 精品一卡2卡3卡四卡网站| 成片一卡2卡3卡4卡网站| 成片一卡二卡三卡四卡|